Home > Effect Plugins > AVA Spectral Compressor
AVA Spectral Compressor
release date: 13.12.2019

AVA Spectral Compressor

 
 
 
Full Product

AAX Native, AU, Mac, VST2, VST3, Win

Download
after successsful payment
$ 69.-

 3.45BestCoinBestCoin Bonus 

Mastering Dynamics Processor

AVA-SC for short, is a dynamics processor that allows you to apply compression selectively across 18 frequency bands. These compression bands can either be spread out across the full range of the spectrum, or focused on a specific frequency range for more precise control.

The AVA Spectral Compressor includes the following features :

  • Master Threshold control
  • Frequency Range selection
  • Band Depth controls
  • Gain Reduction graph
  • Compressor Knee
  • Output Trim

Overview

  • The Depth sliders below the graph control the maximum amount of gain reduction that can be applied to the corresponding frequency bands determined by the current Range setting.

  • The Range can be set to focus on specific areas along the frequency spectrum (Low, Mid, High, etc.), or it can be set to Full Range mode to allow control over the entire spectrum.

  • The Threshold sets the input signal level where the overall compression begins to take effect. Additional controls include compressor Knee and output Trim.

Spectral Compressor GUI

Feature Controls :

  • Threshold - The slider attached to the input meter on the left is the Threshold control. The Threshold sets the input signal level where the overall compression begins to take effect. The Threshold can be set anywhere between -60 and 0 dB.

  • Frequency Range - The Frequency Range section allows you to select the specific frequency range that gets processed by the compressor. The 18 compressor bands will be distributed across whatever range is selected. For example, with Mid selected, all 18 bands will be focused on the Mid range, allowing for more precise control over the frequencies within that range.

The available Frequency Range options are as follows:

  • Full Range: 16 Hz - 20 kHz
  • High: 3 kHz - 20 kHz
  • High Mid: 200 Hz - 18 kHz
  • Mid: 180 Hz - 7 kHz
  • Low Mid: 12 Hz - 8 kHz
  • Low: 15 Hz - 500 Hz

Depth Controls

The 6 sliders below the graph set the Depth for their corresponding bands. The 18 compressor bands are divided among the 6 sliders so that each slider controls the Depth for 3 of those bands. The range of frequencies affected are shown below each slider.

The Depth determines the maximum amount of Gain Reduction that can be applied within each slider’s control range. Possible Depth values range from -24 to 0 dB. Setting a Depth slider to 0 dB will prevent any attenuation from occurring within that slider’s control range.

  • Knee - The Knee value determines the hardness of compression on the input signal as it transitions through the Threshold point. Possible Knee values range from 1 to 30. With a low Knee value (Hard Knee), the compression will activate more abruptly as the signal passes over the Threshold. A high Knee value (Soft Knee) will allow the transients of the input signal to pass through more smoothly, applying compression gradually as they transition through the Threshold point.

  • Output Trim - The Output Trim adjusts the level of the compressor’s output signal anywhere from -10 dB to +10 dB. It can be used to increase or decrease the output level as needed for gain compensation.


 Requirements

Mac:

  • macOS 10.7 or higher (10.10 or higher recommended) 
  • Pro Tools: 10.3.5 or higher; enable the AAX-format during installation
  • Logic: Enable the AU-format during installation
  • Cubase: Enable the VST-and/or VST3-format during installation
  • Most other workstations: Enable the VST-format during installation

Windows:

  • Windows 7 or newer required
  • Pro Tools: 10.3.5 or higher; enable the AAX-format during installation
  • Cubase: Enable the VST-and/or VST3-format during installation
  • Most other workstations: Enable the VST-format during installation
Required Registration:

Harrison Consoles products require you to register with the manufacturer at www.harrisonconsoles.com and with my.plugivery.com/redeem to activate your license.

This product requires an activation!

An internet connection is required to authorize / activate the product.